# SILCARP Suspension Kinematics, Steering Geometry & Alignment Bible
**Document ID:** `SILCARP-MECH-SUSP-001`  
**License:** CERN-OHL-S v2 / CC BY-SA 4.0  
**Target:** Unequal-Length Front Double Wishbone & Rear Independent Trailing Arm  
**Status:** Approved Engineering Specification  

---

## 1. Kinematic Architecture Overview

For an ultra-compact vehicle with a narrow track ($1,250\text{ mm}$ front, $950\text{ mm}$ rear) and an $85\text{–}90\text{ km/h}$ top speed, chassis balance is unforgiving. Poor roll center height or excessive bump steer causes terrifying "dartiness" and roll oversteer.

SILCARP adopts:
1. **Front Suspension:** **Unequal-Length Non-Parallel Double Wishbone (A-arms)** with unequal length ratio ($L_{\text{upper}} / L_{\text{lower}} \approx 0.70$), engineered for negative camber gain in bump.
2. **Rear Suspension:** **Wide-Base Independent Trailing Arms** with integrated anti-roll stiffness, packaging the QS138 transverse motor and reduction transaxle between the pivot bearings.
3. **Manual Steering:** Center-takeoff manual rack (Fiat Seicento / Classic Mini) positioned with co-linear inner tie-rod pivots to achieve **zero bump-steer across $\pm 50\text{ mm}$ wheel travel**.

---

## 2. 3D Suspension Hardpoint Coordinate Table

All coordinates are defined in the vehicle Cartesian frame:
- **Origin $(0,0,0)$:** Ground level at the center of the front axle.
- **$+X$:** Rearward (Longitudinal).
- **$+Y$:** Vehicle Right / Curbside (Lateral).
- **$+Z$:** Upward (Vertical).

```
          Front Double Wishbone Geometry (Front View, Right Side)
    ===================================================================
    Chassis Centerline (Y = 0)
        |
        |      (Y3, Z3) Upper Inboard Pivot
        |         +-----------------------+ (Y_ubj, Z_ubj) Upper Ball Joint
        |        /                         \
        |       /  (Shock Tower)            \ [Steering Knuckle]
        |      /        +                    |
        |     /          \ (Damper)          |  [Wheel Center (Y_wc, Z_wc)]
        |    /            \                  O=====(Disc / Hub)
        |   /              +                 |
        |  /                \ (Lower Mount)  |
        | +------------------+---------------+ (Y_lbj, Z_lbj) Lower Ball Joint
        | (Y1, Z1) Lower Inboard Pivot
    ===================================================================
    Ground Level (Z = 0) ------------------- [Tire Contact Patch (Y=625, Z=0)]
```

### Front Suspension Hardpoints (Right Side, mm)
| Hardpoint Name | $X$ (Longitudinal) | $Y$ (Lateral) | $Z$ (Vertical) | Notes |
| :--- | :--- | :--- | :--- | :--- |
| **Lower Wishbone - Front Pivot** | $+120.0$ | $+210.0$ | $+185.0$ | M12 chassis bush bung |
| **Lower Wishbone - Rear Pivot** | $+380.0$ | $+210.0$ | $+185.0$ | M12 chassis bush bung |
| **Lower Ball Joint (LBJ)** | $+250.0$ | $+575.0$ | $+145.0$ | Fiat 500 pressed joint |
| **Upper Wishbone - Front Pivot** | $+140.0$ | $+285.0$ | $+365.0$ | M10 chassis bush bung |
| **Upper Wishbone - Rear Pivot** | $+360.0$ | $+285.0$ | $+365.0$ | M10 chassis bush bung |
| **Upper Ball Joint (UBJ)** | $+235.0$ | $+535.0$ | $+395.0$ | Offset for caster & KPI |
| **Wheel Center (Nominal Ride)** | $+250.0$ | $+625.0$ | $+280.0$ | $155/65\text{ R14}$ ($r=280\text{mm}$) |
| **Damper Lower Mount** | $+250.0$ | $+430.0$ | $+210.0$ | On lower wishbone |
| **Damper Upper Mount (Duomo)** | $+240.0$ | $+320.0$ | $+490.0$ | Shock tower ring |
| **Steering Tie-Rod Inboard Pivot**| $+150.0$ | $+215.0$ | $+245.0$ | Rack clevis end |
| **Steering Knuckle Outer Tie-Rod**| $+150.0$ | $+560.0$ | $+245.0$ | Forward of wheel center |

---

## 3. Kinematic Alignment Specs & Rationale

| Alignment Parameter | Design Target | Tolerable Range | Engineering Rationale |
| :--- | :--- | :--- | :--- |
| **Static Camber (Front)** | **$-0.5^\circ$** | $-0.3^\circ$ to $-0.8^\circ$ | Compensates for dynamic roll without excessive inside tire wear |
| **Static Camber (Rear)** | **$-1.0^\circ$** | $-0.8^\circ$ to $-1.2^\circ$ | Enhances rear cornering grip to guarantee vehicle stability |
| **Caster Angle (Front)** | **$+4.0^\circ$** | $+3.5^\circ$ to $+4.5^\circ$ | Essential for straight-line self-centering and highway stability |
| **Kingpin Inclination (KPI)** | **$+9.5^\circ$** | $+9.0^\circ$ to $+10.0^\circ$ | Provides steering self-centering weight and camber recovery |
| **Scrub Radius** | **$+10.0\text{ mm}$** | $+8.0\text{ mm}$ to $+14.0\text{ mm}$ | Slightly positive: provides mechanical road feel on unassisted rack |
| **Mechanical Trail** | **$18.5\text{ mm}$** | $16\text{ mm}$ to $22\text{ mm}$ | Self-aligning torque at tire patch |
| **Static Toe (Front)** | **$0.0^\circ$ to $+0.1^\circ$ (Toe-In)**| $0\text{–}1.0\text{ mm}$ total | Eliminates tramlining and improves on-center tracking |
| **Static Toe (Rear)** | **$+0.2^\circ$ (Toe-In)** | $1.5\text{–}2.5\text{ mm}$ total | Stabilizes rear axle under heavy braking |

### Camber Gain Curve in Roll
With an upper-to-lower wishbone length ratio of $\frac{250\text{ mm}}{365\text{ mm}} = 0.685$:
- As the chassis rolls $1.0^\circ$ into a turn, the outside suspension compresses into bump, generating **$-0.62^\circ$ of negative camber recovery**.
- Net outside tire contact angle stays nearly perpendicular to the pavement ($\Delta \theta_{\text{tire}} \le 0.38^\circ$), preventing tire shoulder scrub and maintaining maximum lateral grip ($\ge 0.85\text{g}$).

---

## 4. Steering Kinematics & Ackermann Geometry

### 4.1 Zero Bump-Steer Construction
Bump steer occurs when the steering tie-rod arcs through a different path than the suspension wishbones, causing the front wheels to steer themselves over bumps.

To achieve **zero bump-steer ($\le 0.1\text{ mm}$ toe change across $\pm 50\text{ mm}$ travel)**:
1. The inner tie-rod joint is placed at $Y = 215\text{ mm}$, exactly intersecting the line between the upper and lower inboard wishbone pivot axes.
2. The tie-rod length ($345\text{ mm}$) exactly matches the virtual swing-arm radius of the knuckle steering eye.

### 4.2 Ackermann Sizing & Turning Radius
SILCARP uses **$85\%$ Pro-Ackermann Geometry**:
- The steering rack is mounted forward of the axle centerline ($X = +150\text{ mm}$).
- Knuckle steering arms point outward/forward, ensuring that during a tight corner, the inside front wheel turns sharper than the outside wheel:
  $$\delta_{\text{inside}} = 38.5^\circ \quad / \quad \delta_{\text{outside}} = 31.2^\circ$$
- **Minimum Curb-to-Curb Turning Diameter:**
  $$D_{\text{turn}} = 2 \cdot \left(\frac{L}{\sin \delta_{\text{outside}}}\right) = 2 \cdot \left(\frac{1.56\text{ m}}{\sin 31.2^\circ}\right) = \mathbf{6.02\text{ meters}}$$
  *(Wall-to-wall turning circle: $7.1\text{ meters}$)*. The car can make a complete U-turn within a single standard two-lane residential street without reversing!

---

## 5. Spring, Damper & Ride Frequency Sizing

Vehicle pitch comfort is governed by the **"Flat-Ride Principle"**: the rear suspension must oscillate at a slightly higher natural frequency than the front suspension, so that over a road bump, the rear catch-up motion synchronizes with the front, preventing sickening pitching.

### 5.1 Ride Frequencies
- **Front Natural Ride Frequency:** $f_{n,f} = \mathbf{1.40\text{ Hz}}$ (Plush, compliant urban ride).
- **Rear Natural Ride Frequency:** $f_{n,r} = \mathbf{1.65\text{ Hz}}$ (Settles rear chassis quickly after bumps).

### 5.2 Front Spring Sizing
- Sprung mass per front corner: $m_{s,f} = 125.0\text{ kg}$.
- Target front wheel rate:
  $$K_{w,f} = 4 \cdot \pi^2 \cdot f_{n,f}^2 \cdot m_{s,f} = 4 \cdot (3.1416)^2 \cdot (1.40)^2 \cdot 125.0 = 9,672\text{ N/m} = \mathbf{9.67\text{ N/mm}}$$
- Motion Ratio ($MR$): Damper is mounted at $430\text{ mm}$ on a $575\text{ mm}$ wishbone at a $68^\circ$ installation angle:
  $$MR = \frac{430}{575} \cdot \sin 68^\circ = 0.748 \cdot 0.927 = \mathbf{0.693}$$
- Required Coilover Spring Rate ($K_s$):
  $$K_{s,f} = \frac{K_{w,f}}{MR^2} = \frac{9.67\text{ N/mm}}{(0.693)^2} = 20.14\text{ N/mm} \approx \mathbf{115\text{ lbs/in} \text{ to } 220\text{ lbs/in}}$$
  *(Selecting off-the-shelf $220\text{ lbs/in}$ [$38.5\text{ N/mm}$] Formula Student / UTV coilovers with adjustable preload collar).*

### 5.3 Rear Spring Sizing
- Sprung mass per rear corner: $m_{s,r} = 155.0\text{ kg}$ (includes battery & motor weight).
- Target rear wheel rate ($f_{n,r} = 1.65\text{ Hz}$):
  $$K_{w,r} = 4 \cdot \pi^2 \cdot (1.65)^2 \cdot 155.0 = 16,654\text{ N/m} = \mathbf{16.65\text{ N/mm}}$$
- Rear trailing arm motion ratio: $MR_r = 0.82$.
- Required Rear Coilover Spring Rate:
  $$K_{s,r} = \frac{16.65}{(0.82)^2} = 24.76\text{ N/mm} \approx \mathbf{280\text{ lbs/in}}$$

---

## 6. Suspension Bushings: 3D-Printed High-Toughness TPU

In keeping with the SILCARP Home-Repairability Manifesto:
- **Material:** 3D-printed **TPU 64D or 98A** (Shore hardness) suspension pivot bushings.
- **Construction:** Flanged split-hat bushings pressed into $32\text{ mm}$ tube sleeves with a zinc-plated inner steel sleeve ($16\text{ mm OD} \times 12\text{ mm ID}$).
- **Performance:** Far superior vibration and road harshness dampening compared to harsh metallic Heim joints (spherical rod ends), while offering $10\times$ longer fatigue life than rotting natural rubber. Can be reprinted on any home 3D printer for 25 CZK per bushing.
