# SILCARP Central "Service Spine" Architecture & Modular Loom Schematics
**Document ID:** `SILCARP-ELEC-SPINE-001`  
**License:** CERN-OHL-S v2 / CC BY-SA 4.0  
**Status:** Approved Engineering Specification  

---

## 1. Architectural Philosophy: The Service Spine

In conventional micro-vehicles and legacy passenger cars, automotive electronics and hydraulics are buried behind injection-molded dashboards, under carpeting, or exposed to road spray behind front wheel arches. Troubleshooting an electrical fault or bleeding brakes requires hours of destructive interior disassembly.

**The SILCARP Service Spine** concentrates 100% of the vehicle’s primary control electronics, low-voltage power distribution, brake hydraulics, and diagnostic telemetry into a **single, dry, centralized tunnel bay** located between the driver and passenger seats.

```
                  Top-Down View of SILCARP Cabin Floorpan
    ===================================================================
    [ Front Door Aperture / Steer Pedestal / Pedal Box ]
    -------------------------------------------------------------------
       [Driver Footwell]            ||           [Passenger Footwell]
                                    ||
                                    ||
       +----------------------------++----------------------------+
       |                            ||                            |
       |                            ||  [ THE SERVICE SPINE ]     |
       |                            ||  Weather-Sealed Al Hatch   |
       |                            ||  (Quick-Release Cam Latches)
       |       [ Driver Seat ]      ||                            |
       |                            ||  - ZombieVerter VCU        |
       |                            ||  - Bussmann Fuse/Relay Box |
       |                            ||  - 72V->12V DC-DC Conv     |
       |                            ||  - Brake Bias & Master Cyl |
       |                            ||  - CAN Diagnostic / Wi-Fi  |
       |                            ||                            |
       +----------------------------++----------------------------+
                                    ||
    -------------------------------------------------------------------
    [ Rear Bulkhead / 72V Traction Battery Bay / Trampa VESC Inverter ]
    ===================================================================
```

---

## 2. Mechanical Packaging & Dimensions

- **Bay Location:** Central chassis tunnel, spanning from the front dashboard firewall to the rear battery bulkhead.
- **Envelope:** $780\text{ mm}$ (Length) $\times 180\text{ mm}$ (Width) $\times 160\text{ mm}$ (Depth).
- **Enclosure Construction:** $2.0\text{ mm}$ folded 5052-H32 aluminum sheet box welded into the central spaceframe ladder tubes.
- **Top Hatch Lid:** $3\text{ mm}$ aluminum diamond-plate or powder-coated flush panel sealed with an automotive neoprene gasket and secured with four Southco quarter-turn wing-head cam fasteners (no tools required to open).
- **Environment:** IP65 sealed when latched; equipped with an internal Gore-Tex pressure equalization vent.

---

## 3. Component Layout along the Spine

Components are organized linearly from front to rear along a standardized DIN rail / slotted aluminum backplate:

```
+-----------------------------------------------------------------------------+
| FRONT (Firewall)                                                REAR (Pack) |
+------------------+------------------+-------------------+-------------------+
| [ HYDRAULIC BAY ]| [ 12V LOW-VOLT ] | [ CONTROL BRAIN ] | [ HV BUS / VESC ] |
|                  |                  |                   |                   |
| - Dual Master    | - Cooper Bussmann| - ZombieVerter    | - Trampa VESC     |
|   Cylinders      |   15300 Fuse/    |   VCU (Delphi 56p)|   100/250 Inverter|
|   (Brembo 0.70") |   Relay Box      | - CAN Bus Term    | - Gigavac GX14    |
| - Balance Bar    | - 72V->12V 30A   | - LilyGO T-CAN485 |   400A Contactor  |
| - Remote Reserv. |   Isolated DC-DC |   BMS Gateway     | - Pre-charge relay|
+------------------+------------------+-------------------+-------------------+
```

### 3.1 Hydraulic Bay (Front Section)
- **Brake Master Cylinders:** Dual Wilwood / Brembo compact flange cylinders (0.70" front circuit, 0.625" rear circuit).
- **Balance Bar:** Mechanical threaded bias bar directly linked to the brake pedal pushrod, allowing mechanical front/rear brake force tuning.
- **Reservoirs:** Dual clear reservoirs mounted at the very top edge of the spine, visible through an inspection sight glass in the lid.

### 3.2 12V Power Distribution Bay (Center-Front)
- **Power Distribution Unit:** **Cooper Bussmann Series 15300 RTMR** (Rear Terminal Mini Fuse & Relay).
  - Weatherproof IP66 enclosure.
  - Accommodates 10 standard mini-relays (Bosch style) and 20 mini blade fuses (ATO/ATC).
  - Supplies headlights, turn signals, horn, wiper, brake lights, hazard circuit, and VCU ignition.
- **DC-DC Converter:** Mean Well or Sevcon 72V-to-13.8V isolated buck converter (30A continuous, 400W peak), mounted directly to the aluminum spine floor for chassis heatsinking.

### 3.3 Control Brain & CAN Bus Bay (Center-Rear)
- **Vehicle Control Unit (VCU):** **ZombieVerter VCU v2** in an IP67 die-cast aluminum enclosure with Delphi 56-pin automotive connector.
- **Wireless Diagnostics:** ESP8266/ESP32 on-board Wi-Fi transmitter creates a local hotspot (`SILCARP-VCU-WIFI`), serving a real-time calibration dashboard to any smartphone browser (zero specialized OBD2 scan tools required).
- **BMS Bridge:** LilyGO T-CAN485 module bridging the JK-BMS or VW MEB slave modules to the main 500 kbps automotive CAN bus.

### 3.4 High-Voltage & Inverter Bay (Rear Section)
- **Inverter:** **Trampa VESC 100/250** mounted to an internal aluminum cold plate, interfacing with the QS Motor 138 90H PMSM.
- **Main Contactor:** Gigavac `GX14BA` 400A hermetically sealed contactor.
- **Pre-Charge Circuit:** $50\,\Omega / 50\text{W}$ aluminum-housed wirewound resistor switched via a 12V Song Chuan sealed relay, providing 850 ms pre-charge time before main contactor closure.

---

## 4. The 4 Modular Sub-Loom Harnesses (Deutsch DT Disconnects)

Instead of a 20 kg monolithic harness, the vehicle is partitioned into **four self-contained sub-looms** that click into bulkhead connectors on the Service Spine:

```
                           +----------------------+
                           |    SERVICE SPINE     |
                           |  CENTRAL HARNESS HUB |
                           +----------+-----------+
                                      |
         +----------------+-----------+-----------+----------------+
         |                |                       |                |
         v                v                       v                v
     [ POD 1 ]        [ POD 2 ]               [ POD 3 ]        [ POD 4 ]
   Front Lighting   Front Ingress           Rear Powertrain    72V Traction
   & Wiper Loom     Door Loom               & Inverter Loom    Battery & BMS
   (Deutsch DT-12)  (Deutsch DT-8)          (Deutsch DT-12)    (Amphenol HVS)
```

### Pod 1: Front Lighting & Wiper Loom (Deutsch DT-12)
- Pin 1: Low Beam Left/Right (+12V)
- Pin 2: High Beam (+12V)
- Pin 3: Front Left Turn Signal (+12V)
- Pin 4: Front Right Turn Signal (+12V)
- Pin 5: Daytime Running Lights (DRL)
- Pin 6: Wiper Motor Low Speed
- Pin 7: Wiper Motor High Speed
- Pin 8: Wiper Park Return Switch
- Pin 9: Windshield Washer Pump (+12V)
- Pin 10: Horn Relay Output (+12V)
- Pin 11–12: Heavy Chassis Ground (AWG 14)

### Pod 2: Front Ingress Door Loom (Deutsch DT-8)
Runs through a heavy-duty flexible EPDM rubber bellows at the A-pillar hinge:
- Pin 1: Upper Latch Interlock Microswitch (Normally Open, closes on Stage 2)
- Pin 2: Lower Latch Interlock Microswitch (Series loop)
- Pin 3: Interior Courtesy Dome Light (+12V switched)
- Pin 4: Hazard / Central Lock Actuator (Optional)
- Pin 5–8: Spare auxiliary / Heated windshield elements

### Pod 3: Rear Powertrain & Inverter Loom (Deutsch DT-12)
- Pin 1–2: Shielded CAN Bus (`CAN_H`, `CAN_L` 500 kbps)
- Pin 3: Inverter Enable (+12V ignition run)
- Pin 4: Throttle 0–5V Signal 1 (Hall sensor)
- Pin 5: Throttle 0–5V Signal 2 (Redundant safety inverse)
- Pin 6: Brake Pressure Switch (+12V)
- Pin 7: Motor Temperature Thermistor (KTY84)
- Pin 8: Reverse Direction Switch
- Pin 9: Handbrake Interlock Switch
- Pin 10–12: Sensor 5V & Ground Reference

### Pod 4: Battery & BMS Pod (Amphenol Radsok + Deutsch DT-6)
- High Voltage: Dual $35\text{ mm}^2$ flexible orange silicon cables with Amphenol Radsok quick-disconnect lugs.
- Low Voltage / Control:
  - Pin 1–2: BMS CAN Bus (`BMS_CAN_H`, `BMS_CAN_L`)
  - Pin 3: Manual Service Disconnect (MSD) Interlock Loop
  - Pin 4: Pack Pre-Charge Sense
  - Pin 5–6: Pack Contactor Economizer Drive (+12V PWM)

---

## 5. Right-to-Repair Serviceability Benchmarks

1. **Relay / Fuse Replacement:** < 60 seconds (open hatch, inspect label map on underside of lid, swap mini-fuse).
2. **VCU Firmware Flash:** < 3 minutes (connect smartphone to `SILCARP-VCU-WIFI`, upload binary via web UI).
3. **Brake Fluid Bleeding:** < 15 minutes (top-access master cylinder reservoirs, clear sight glass).
4. **Sub-Loom Bench Repair:** < 10 minutes to unclick Pod Deutsch connector and remove harness onto a workshop table.
