# SILCARP Dual-Circuit Hydraulic Braking Calculations & Bias Tuning
**Document ID:** `SILCARP-MECH-BRAKE-001`  
**License:** CERN-OHL-S v2 / CC BY-SA 4.0  
**Regulatory Anchor:** EU Regulation 3/2014 Annex III & UNECE Regulation No. 13-H  
**Status:** Approved Engineering Specification  

---

## 1. System Requirements & Baseline Parameters

To satisfy EU L7e-CP homologation without the weight, vacuum lines, and failure modes of a vacuum brake booster, SILCARP uses an unassisted **dual-circuit hydraulic brake pedal box with an adjustable balance bar**.

### 1.1 Vehicle Inertial Parameters
| Parameter | Symbol | Value | Unit | Notes |
| :--- | :--- | :--- | :--- | :--- |
| **Gross Vehicle Weight (Laden)** | $m$ | 650.0 | $\text{kg}$ | 2 occupants ($85\text{ kg} \times 2$) + $45\text{ kg}$ luggage |
| **Wheelbase** | $L$ | 1.560 | $\text{m}$ | Center-to-center distance |
| **Center of Gravity Height** | $h_{\text{cg}}$ | 0.420 | $\text{m}$ | Low battery placement below floor |
| **Static Weight Distribution** | $W_f / W_r$ | 50 / 50 | $\%$ | $325\text{ kg}$ Front / $325\text{ kg}$ Rear |
| **Effective Rolling Radius** | $r_{\text{tire}}$ | 0.280 | $\text{m}$ | 155/65 R14 all-season tires |
| **Target Peak Deceleration** | $a$ | 0.85 | $\text{g}$ | $8.34\text{ m/s}^2$ on dry asphalt |
| **Tire-Road Friction Coeff.** | $\mu_{\text{road}}$ | 0.90 | — | Dry tarmac |
| **Brake Pad Friction Coeff.** | $\mu_{\text{pad}}$ | 0.38 | — | Standard road organic pads (Ferodo FDB1397) |

---

## 2. Dynamic Weight Transfer Analysis

Under aggressive braking at $a = 0.85\text{g}$ ($8.34\text{ m/s}^2$), forward longitudinal inertia transfers load from the rear axle onto the front axle:

$$\Delta W = \frac{m \cdot a \cdot h_{\text{cg}}}{L} = \frac{650 \cdot 0.85 \cdot 0.420}{1.560} = 148.75\text{ kg} \quad (1,459\text{ N})$$

### Dynamic Axle Normal Loads:
- **Front Axle Dynamic Load:**
  $$F_{z,f} = \left(\frac{W_f}{100} \cdot m + \Delta W\right) \cdot g = (325 + 148.75) \cdot 9.81 = 4,648\text{ N} \quad (\mathbf{72.9\%})$$
- **Rear Axle Dynamic Load:**
  $$F_{z,r} = \left(\frac{W_r}{100} \cdot m - \Delta W\right) \cdot g = (325 - 148.75) \cdot 9.81 = 1,729\text{ N} \quad (\mathbf{27.1\%})$$

> **Crucial Stability Invariant (UNECE 13-H):**  
> Under all load conditions, the front wheels MUST lock up before the rear wheels to prevent dangerous snap-oversteer or vehicle spin.  
> **Target Brake Torque Bias: 70% Front / 30% Rear.**

---

## 3. Caliper & Rotor Sizing (Fiat 500 Standard)

### 3.1 Front Axle Sizing
- **Caliper:** Fiat 500 / Panda TRW single-piston floating caliper.
  - Piston Diameter: $D_{p,f} = 48\text{ mm}$ ($0.048\text{ m}$).
  - Piston Area: $A_{p,f} = \frac{\pi}{4} \cdot (48)^2 = 1,809.6\text{ mm}^2$ ($1.810 \times 10^{-3}\text{ m}^2$).
- **Rotor:** Vented Disc $\varnothing 240\times 20\text{ mm}$, `4×100 mm` PCD, `57.1 mm` center bore (VW Lupo / Polo 6N — Brembo `08.4177.10`, directly mating with the `SKF VKBA 3596` `4×100` hub).
  - Effective Friction Radius: $r_{\text{eff},f} = 102\text{ mm}$ ($0.102\text{ m}$).

### 3.2 Rear Axle Sizing
- **Caliper:** Lucas/TRW 34 mm rear floating caliper with integrated mechanical handbrake.
  - Piston Diameter: $D_{p,r} = 34\text{ mm}$ ($0.034\text{ m}$).
  - Piston Area: $A_{p,r} = \frac{\pi}{4} \cdot (34)^2 = 907.9\text{ mm}^2$ ($9.079 \times 10^{-4}\text{ m}^2$).
- **Rotor:** Solid Disc $\varnothing 226\text{–}240\text{ mm}$, `4×100 mm` PCD, `57.1 mm` center bore (VW Golf III / Polo 6N — Brembo `08.7165.14` / `08.4177.10`).
  - Effective Friction Radius: $r_{\text{eff},r} = 104\text{ mm}$ ($0.104\text{ m}$).

---

## 4. Master Cylinder Selection & Pedal Ratio

### 4.1 Pedal Leverage Ratio
To keep driver pedal effort comfortable without a vacuum servo, we select a **mechanical pedal ratio of $5.5 : 1$**:
$$R_{\text{pedal}} = \frac{L_{\text{foot}}}{L_{\text{pivot}}} = 5.5$$
For a nominal firm emergency stop, the driver applies **$F_{\text{foot}} = 350\text{ N}$** ($\approx 35\text{ kgf}$), producing a balance bar input force of:
$$F_{\text{bar}} = F_{\text{foot}} \cdot R_{\text{pedal}} = 350 \cdot 5.5 = \mathbf{1,925\text{ N}}$$

### 4.2 Balance Bar Force Distribution
With the balance bar tuned to a **$70\% / 30\%$** split:
- **Front Master Cylinder Pushrod:** $F_{\text{push},f} = 1,925 \cdot 0.70 = 1,347.5\text{ N}$
- **Rear Master Cylinder Pushrod:** $F_{\text{push},r} = 1,925 \cdot 0.30 = 577.5\text{ N}$

### 4.3 Hydraulic Master Cylinder Bores
- **Front Master Cylinder:** $0.70"$ ($17.8\text{ mm}$) bore (Wilwood / Brembo compact flange).
  - Area: $A_{\text{mc},f} = \frac{\pi}{4} \cdot (17.8)^2 = 248.8\text{ mm}^2$ ($2.488 \times 10^{-4}\text{ m}^2$).
  - Front Line Pressure:
    $$P_{\text{line},f} = \frac{F_{\text{push},f}}{A_{\text{mc},f}} = \frac{1,347.5\text{ N}}{248.8 \times 10^{-6}\text{ m}^2} = 5.416 \times 10^6\text{ Pa} = \mathbf{54.2\text{ bar}}$$
- **Rear Master Cylinder:** $0.625"$ ($15.9\text{ mm}$) bore.
  - Area: $A_{\text{mc},r} = \frac{\pi}{4} \cdot (15.9)^2 = 198.6\text{ mm}^2$ ($1.986 \times 10^{-4}\text{ m}^2$).
  - Rear Line Pressure:
    $$P_{\text{line},r} = \frac{F_{\text{push},r}}{A_{\text{mc},r}} = \frac{577.5\text{ N}}{198.6 \times 10^{-6}\text{ m}^2} = 2.908 \times 10^6\text{ Pa} = \mathbf{29.1\text{ bar}}$$

---

## 5. Total Braking Force & Deceleration Check

### 5.1 Front Wheel Braking Torque & Force (2 Wheels)
- Caliper Clamping Force:
  $$F_{\text{clamp},f} = P_{\text{line},f} \cdot A_{p,f} = (54.2 \times 10^5\text{ Pa}) \cdot (18.10 \times 10^{-4}\text{ m}^2) = 9,810\text{ N}$$
- Brake Torque per Front Rotor (2 friction surfaces):
  $$T_{\text{brake},f} = 2 \cdot \mu_{\text{pad}} \cdot F_{\text{clamp},f} \cdot r_{\text{eff},f} = 2 \cdot 0.38 \cdot 9,810 \cdot 0.102 = \mathbf{760.4\text{ Nm}}$$
- Front Road Braking Force:
  $$F_{\text{tractive},f} = 2 \cdot \left(\frac{T_{\text{brake},f}}{r_{\text{tire}}}\right) = 2 \cdot \left(\frac{760.4}{0.280}\right) = \mathbf{5,431\text{ N}}$$

### 5.2 Rear Wheel Braking Torque & Force (2 Wheels)
- Caliper Clamping Force:
  $$F_{\text{clamp},r} = P_{\text{line},r} \cdot A_{p,r} = (29.1 \times 10^5\text{ Pa}) \cdot (9.079 \times 10^{-4}\text{ m}^2) = 2,642\text{ N}$$
- Brake Torque per Rear Rotor:
  $$T_{\text{brake},r} = 2 \cdot \mu_{\text{pad}} \cdot F_{\text{clamp},r} \cdot r_{\text{eff},r} = 2 \cdot 0.38 \cdot 2,642 \cdot 0.104 = \mathbf{208.8\text{ Nm}}$$
- Rear Road Braking Force:
  $$F_{\text{tractive},r} = 2 \cdot \left(\frac{T_{\text{brake},r}}{r_{\text{tire}}}\right) = 2 \cdot \left(\frac{208.8}{0.280}\right) = \mathbf{1,491\text{ N}}$$

### 5.3 Combined Deceleration
- **Total Braking Force:**
  $$F_{\text{total}} = F_{\text{tractive},f} + F_{\text{tractive},r} = 5,431 + 1,491 = \mathbf{6,922\text{ N}}$$
- **Achieved Deceleration:**
  $$a_{\text{achieved}} = \frac{F_{\text{total}}}{m} = \frac{6,922\text{ N}}{650\text{ kg}} = 10.65\text{ m/s}^2 = \mathbf{1.08\text{ g}}$$

> **Validation Verdict:**  
> The system achieves $> 0.85\text{g}$ deceleration at only $275\text{ N}$ pedal effort ($28\text{ kgf}$), well within normal human leg capacity without requiring a brake booster.  
> The front-to-rear force ratio is $\frac{5,431}{6,922} = \mathbf{78.5\%}$, guaranteeing complete directional stability and zero rear-wheel pre-lockup.

---

## 6. Regenerative Braking Blending Strategy

The ZombieVerter VCU reads an inline hydraulic pressure transducer (`SensorTech 0–100 bar`, $0.5\text{–}4.5\text{V}$) on the front brake circuit:
1. **Deadband ($0\text{–}5\text{ bar}$):** Pad touch / pedal take-up. Inverter commands light coasting regen ($0.05\text{g}$).
2. **Low-Speed Linear Regen ($5\text{–}20\text{ bar}$):** Motor negative torque scales linearly up to $0.20\text{g}$ deceleration (capturing up to $9\text{ kW}$ peak regen into battery/ultracap). Friction pads provide minimal wear.
3. **Emergency Braking ($> 20\text{ bar}$):** Friction pads dominate. If ABS or wheel slip occurs, VCU automatically dials back motor regen torque in $< 10\text{ ms}$ to maintain tire grip.
