# SILCARP 72V Modular Battery Cassette & BMS Engineering Specification
**Document ID:** `SILCARP-ELEC-BATT-001`  
**License:** CERN-OHL-S v2 / CC BY-SA 4.0  
**Regulatory Anchor:** EU Regulation 3/2014 Annex IV & UNECE Regulation No. 100 (Rechargeable Energy Storage System - REESS)  
**Status:** Approved Engineering Specification  

---

## 1. Executive Summary & Dual-Chemistry Strategy

The traction battery is the heaviest, most hazardous, and most expensive subsystem of an electric vehicle. Automotive OEMs use "Cell-to-Pack" (CTP) construction where cells are permanently submerged in polyurethane structural foam—meaning a single weak cell ruins the entire pack.

SILCARP introduces the **Bolt-Together Modular Battery Cassette**:
- **100% Demountable:** Cells are held in mechanical compression trays using threaded rods; zero structural glue.
- **10 mm Socket Serviceability:** Any individual cell or module can be inspected, voltage-tested, and replaced in a home garage in under 40 minutes using standard metric hand tools.
- **Dual Chemistry / Source Architecture:**
  - **Path A (Production Benchmark):** 24S LiFePO4 (LFP) using prismatic cells (EVE `LF105` 105Ah, 8.06 kWh or `LF230` 230Ah, 17.6 kWh). Intrinsically safe (no thermal runaway propagation at $< 210^\circ\text{C}$), $> 3,500$ cycle life.
  - **Path B (Rapid Mule / Salvage Sweet-Spot):** Dual Škoda Enyaq / VW ID.3 MEB 12S modules in series (24S NCM 712, 88.8V nominal, 13.7 kWh, 63 kg total cell mass). Readily available on European salvage markets for ~35,000–45,000 CZK total.

---

## 2. Path A: 24S Prismatic LFP Cassette Architecture

```
            24S Prismatic Battery Cassette Layout (Top View)
 +========================================================================+
 |  [ FRONT OF PACK - High-Voltage Junction & Contactor Bay (220 mm) ]    |
 |  +------------------------------------------------------------------+  |
 |  | Gigavac GX14 Contactor (+) | Gigavac GX14 Contactor (-)          |  |
 |  | 50W Pre-charge Resistor   | Pre-charge Relay | Class T 400A Fuse |  |
 |  | Amphenol Radsok MSD Plug   | Bender A-ISOMETER Isolation Sensor  |  |
 |  +------------------------------------------------------------------+  |
 +========================================================================+
 |  [ CELL BAY - 2 Rows of 12 Prismatic Cells (EVE LF105) (640 mm) ]     |
 |                                                                        |
 |  [Al Endplate (6mm)]                               [Al Endplate (6mm)] |
 |  |=================|  M8 Steel Tie-Rods (x4)       |=================| |
 |  |  Cell #1 to #12 |==============================>| Cell #13 to #24 | |
 |  |  Row 1 (12S)    |                               |  Row 2 (12S)    | |
 |  |=================|                               |=================| |
 |                                                                        |
 |  <- 0.5mm FR4 Insulator between all cells | Flexible Cu Busbars (M6) ->|
 +========================================================================+
```

### 2.1 Cell Specifications (EVE LF105)
| Parameter | Value | Unit | Notes |
| :--- | :--- | :--- | :--- |
| **Chemistry** | Lithium Iron Phosphate (LiFePO4) | — | Extremely high thermal stability |
| **Cell Dimensions** | $130.3 \times 36.7 \times 200.5$ | $\text{mm}$ | Standard aluminum prismatic shell |
| **Cell Mass** | $1.98 \pm 0.05$ | $\text{kg}$ | Total cell mass: $47.5\text{ kg}$ (24 cells) |
| **Nominal Voltage** | $3.20$ | $\text{V}$ | 24S Pack: $76.8\text{ V}$ nominal |
| **Operating Voltage Window** | $2.50\text{–}3.65$ | $\text{V}$ | Pack: $60.0\text{–}87.6\text{ V}$ |
| **Rated Capacity** | $105.0$ | $\text{Ah}$ | $336\text{ Wh}$ per cell |
| **Total Pack Energy** | **$8.06$** | $\text{kWh}$ | Real-world urban range: $105\text{–}125\text{ km}$ |
| **Max Continuous Discharge**| $1.0\text{C} = 105\text{ A}$ | $\text{A}$ | Continuous power: $8.06\text{ kW}$ |
| **Peak 30s Pulse Discharge**| $3.0\text{C} = 315\text{ A}$ | $\text{A}$ | Peak power: $24.2\text{ kW}$ (VESC limit) |

---

## 3. Mechanical Clamping & Swelling Prevention

Prismatic LFP cells expand and contract during charge/discharge cycling. If left unconstrained, microscopic delamination occurs, reducing cycle life by up to $50\%$.

### Clamping Force Calculation
Manufacturer specification requires continuous mechanical compression of **$300\text{ kgf} \pm 20\text{ kgf}$** ($2,940\text{ N}$, corresponding to $\approx 12\text{ psi}$ on the cell face):
- **End-Plates:** Two $6.0\text{ mm}$ CNC-machined 6061-T6 aluminum plates stiffened with welded vertical ribs.
- **Tie-Rods:** Four M8 Grade 8.8 zinc-plated threaded steel rods spanning the length of each 12-cell stack.
- **Belleville Disc Springs:** Two Belleville spring washers (DIN 2093, $16 \times 8.2 \times 0.9\text{ mm}$) stacked in series under each M8 flange nut. The disc springs absorb cyclic thermal expansion while maintaining a constant $735\text{ N}$ tensile clamp force per rod ($4 \times 735\text{ N} = 2,940\text{ N}$ total).
- **Inter-Cell Dielectric:** $0.5\text{ mm}$ FR4 epoxy-fiberglass sheets placed between adjacent cells to prevent chafing and provide $5,000\text{ V}$ breakdown isolation.

---

## 4. High-Voltage Busbars, Fusing & Contactor Bay

```
           High-Voltage Schematics & Contactor Sequencing
           
   Pack (+) ──[Class T 400A]──[Gigavac GX14 (+)]──┬───────────> HV+ (To Inverter)
                                                  │
                                          [Precharge Relay]
                                                  │
                                           [50 Ohm 50W Resistor]
                                                  │
                                                  ├───────────> (Precharge Node)
   Pack (-) ──────────────────[Gigavac GX14 (-)]──┴───────────> HV- (To Inverter)
                                   │
                           [Amphenol MSD Plug]
```

### 4.1 Busbar Design & Bolted Fasteners
- **Material:** $2.0\text{ mm} \times 20\text{ mm}$ pure copper (C11000), electro-tin plated (or nickel-plated) to prevent galvanic corrosion against aluminum cell terminals.
- **Form:** Omega-curved ($\Omega$-shaped) flexible stress relief bend in the center of each busbar, allowing $1.5\text{ mm}$ longitudinal compliance under vibration without straining cell terminal studs.
- **Terminal Fasteners:** Stainless steel M6 serrated flange nuts. **Torque specification: $4.5\text{ Nm}$** (checked with calibrated torque wrench; anti-tamper paint mark applied).

### 4.2 Protection & Fusing
1. **Primary Traction Fuse:** **Littlefuse / Bussmann Class T 400A (Fast-Acting, 200 kA Interrupting Rating, DC 160V rated)**. Mounted on the positive terminal post inside the pack.
2. **Manual Service Disconnect (MSD):** **Amphenol Radsok 2-Pole High-Current MSD** with integrated low-voltage High-Voltage Interlock Loop (HVIL). Pulling the orange handle physically severs the center of the series string (splitting the pack into two harmless $\le 38.4\text{V}$ halves) and opens the 12V contactor coil interlock.
3. **High-Voltage Contactors:** Dual **Gigavac `GX14BA` 400A hermetically sealed contactors** with integrated coil economizers ($12\text{V}$ pull-in, $0.15\text{A}$ hold).
4. **Pre-charge Circuit:** $50\,\Omega$ $50\text{W}$ aluminum-clad wirewound resistor switched via a Song Chuan 12V automotive sealed relay, controlled by the ZombieVerter VCU. Precharge duration: $850\text{ ms}$.

---

## 5. Battery Management System (BMS) & Thermal Sense

### 5.1 BMS Hardware: JK-BMS 24S 200A (Active Balancing)
- **Active Balancing:** 2.0A active supercapacitor charge-transfer balancing. Unlike wasteful passive bleed resistors that generate excessive heat in a sealed enclosure, active balancing transfers energy from the highest cell to the lowest cell with $> 85\%$ efficiency.
- **Sense Harness:** 25-pin automotive sealed connector with $0.5\text{ mm}^2$ PTFE-insulated sense wires, individual $1\text{A}$ inline fuses on every cell tap, and silicone wire loom sleeving.
- **Temperature Sensing:** Four NTC $10\text{k}\Omega$ temperature probes positioned at:
  - Sensor 1: Center cell of Row 1 (hot spot).
  - Sensor 2: Negative terminal busbar.
  - Sensor 3: Center cell of Row 2.
  - Sensor 4: Positive terminal busbar near main fuse.

### 5.2 CAN Bus Bridge Architecture
The JK-BMS communicates internally over isolated RS485. An ultra-compact **LilyGO T-CAN485** module ($15 open-source ESP32 board running `esphome-jk-bms-can`) translates BMS registers into standard automotive CAN frames (`0x300`, `0x301`, `0x302`) at 500 kbps, feeding live telemetry directly into the ZombieVerter VCU and RealDash display.

---

## 6. Path B: Salvage Škoda Enyaq MEB 12S Quick-Mule Route

For builders wanting maximum kWh per Euro without assembling 24 raw prismatic cells:

```
+=============================================================================+
| ŠKODA ENYAQ / VW ID.3 MEB 12S MODULE INTEGRATION                           |
+=============================================================================+
| Configuration       | 2 Modules in Series (12S + 12S = 24S)                 |
| Chemistry           | LG Chem / CATL NCM 712 (Lithium Nickel-Cobalt-Manganese)
| Pack Voltage        | 88.8V Nominal (72.0V empty, 100.8V full)             |
| Pack Capacity       | 156 Ah (13.7 kWh usable energy)                      |
| Pack Dimensions     | 2x (590 mm x 225 mm x 110 mm) modules side-by-side    |
| Total Cell Mass     | 63.0 kg (31.5 kg per module)                          |
| Range Potential     | ~170–190 km in urban driving                          |
| Interfacing         | ZombieVerter VCU native MEB CAN on connector 0Z1971690|
+=============================================================================+
```

* **Safety Note:** MEB modules operate up to $100.8\text{V}$ DC at 100% SoC. The Trampa VESC 100/250 has an absolute maximum rating of $100\text{V}$. When using 2× MEB modules with the VESC 100/250, **charge termination voltage MUST be capped at $4.10\text{V}$ per cell ($98.4\text{V}$ pack voltage)**. This provides a $1.6\text{V}$ safety headroom while delivering $96\%$ of total capacity and extending battery cycle life by $300\%$.

---

## 7. Enclosure & Environmental Protection

- **Case Material:** $2.5\text{ mm}$ laser-cut 5052-H32 aluminum sheet with folded and TIG-welded corner seams.
- **Lid Sealing:** Closed-cell automotive EPDM sponge gasket ($15 \times 3\text{ mm}$) compressed by 24 perimeter M6 stainless flange bolts.
- **Ingress Rating:** Tested to IP67 (submersion to $1.0\text{ m}$ for 30 minutes).
- **Pressure Vent:** Center-mounted automotive Gore-Tex membrane vent (`Gore Automotive Vent AVS 200`) providing bidirectional vapor breathability while remaining watertight, preventing pressure differential buildup during altitude or ambient temperature swings.
- **Chassis Mounting:** Four reinforced M10 grade 10.9 bungs welded to the enclosure bottom, bolting directly into captive crossmembers of the lower spaceframe ladder.
